How to read your city water quality report (CCR) in 10 minutes

A plain guide to your annual water quality report: where to find it, what MCL and ppm mean, and where hardness hides, using Dallas and Phoenix as examples.

Your water utility publishes a report every year that shows what is in your tap water. It looks like a wall of tables, but you only need a few parts of it. This guide shows you where to look, using two real reports as examples: Dallas, TX and Phoenix, AZ.

Minute 1: Get the right report

The EPA requires community water systems to deliver a Consumer Confidence Report (CCR), also called an annual drinking water quality report. Per the EPA, it must be sent each year by July 1 (EPA, “CCR Information for Consumers”, accessed November 18, 2026).

To find yours:

  • Search “[your city] water quality report” and open the utility’s own site (usually ending in .gov)
  • Check that the utility named on the report matches the one on your water bill. Neighboring cities often run separate systems.
  • If you can’t find it, call your water supplier, or use the CCR search tool linked from the EPA consumer page

Examples:

Minutes 2 to 3: Check the year and the source water

Look at the cover or first page for the report year. Both example reports above are 2025.

Then find the “where does our water come from” section. It tells you whether your water is from lakes and rivers or from wells, which is a big part of why water is hard or soft. For example, the Phoenix 2025 report says about 97 to 99 percent of its 2025 water was surface water, mainly from the Salt, Verde, and Colorado rivers, with the rest from about 20 city groundwater wells.

Minutes 3 to 5: Learn the five terms that unlock the tables

Most reports include a definitions box. These are the terms you’ll see most, quoted from the City of Dallas 2025 report:

Term What the report says it means
MCL “Maximum Contaminant Level is the highest level of a contaminant that is allowed in drinking water.”
MCLG “Maximum Contaminant Level Goal is the level of a contaminant in drinking water below which there is no known or expected risk to health.”
AL “Action Level is the concentration of a contaminant which, if exceeded, triggers treatment or other requirements that a water system must follow.”
ppm “parts per million, or milligrams per liter (mg/L)”
ppb “parts per billion, or micrograms per liter (ug/L)”

Also watch for ND, which means “Not Detected.”

Quick check: 1 ppm is 1,000 ppb. Always look at the units column before comparing a number to a limit.

Minutes 5 to 7: Read one row of the main table

Each row usually shows: the substance, the year sampled, the level found (an average or highest value), the range (minimum to maximum), the MCL, the MCLG, the unit, and the likely source.

How to read it: compare the level found with the MCL in the same units. If the level is below the MCL, that substance met the federal limit. If there was a violation, look for it to be flagged in the table or explained in the text.

Example from the Dallas 2025 report (full data version): Nitrate (as N), year 2025, average 0.671, range 0.587 to 0.802, MCL 10, unit ppm. The highest Dallas reading is well under the limit of 10.

Minutes 7 to 9: Find hardness (it may be hiding, or missing)

Hardness is not a health-based standard, so it’s usually in a separate table of “aesthetic” or “secondary” items, or not in the report at all.

  • Phoenix 2025: look for the table titled “2025 Aesthetic Water Quality Analysis from Distribution System & Secondary Drinking Water Guidelines.” The row reads Total Hardness: 172 - 302 ppm / 10 - 17.6 grains per gallon. The report notes that taste, odor, and hardness “are not regulated under drinking water health standards.” Full Phoenix breakdown.
  • Dallas 2025: the report lists no hardness figure. Dallas Water Utilities stated the range separately, 120 to 155 mg/L as CaCO3, in a December 1, 2023 memo. Full Dallas breakdown.

If your report has no hardness number, call the utility’s water quality line (usually listed in the report) or test your own tap.

Convert hardness to grains per gallon

Softeners and test strips use grains per gallon (gpg). Divide mg/L (ppm) by 17.1:

gpg = mg/L ÷ 17.1 Example: 172 ÷ 17.1 = 10.1 gpg (Phoenix prints 10)

Compare to the USGS scale

From the USGS Water Science School (accessed November 18, 2026):

USGS class mg/L as calcium carbonate About grains per gallon (our math, ÷ 17.1)
Soft 0 to 60 0 to 3.5
Moderately hard 61 to 120 3.6 to 7.0
Hard 121 to 180 7.1 to 10.5
Very hard more than 180 more than 10.5

Minute 10: Note the contacts and what to do next

Before closing the report, write down:

  • The utility’s water quality phone or email (Phoenix lists WSDCompliance@phoenix.gov and 602-262-6251. Dallas lists 3-1-1 and DWU at 214-670-0915.)
  • The report year, so you know when to check for the next one (by July 1 each year, per the EPA)

Then decide:

  • Concern about a regulated substance? Contact your utility first, using the contacts in the report.
  • Hardness only? That’s a plumbing and cleaning question. See our city pages for when vinegar cleaning is enough and when a softener makes sense.

A note on home treatment

The Phoenix report warns that if you install home treatment, “failure to follow the manufacturer’s instructions concerning operation and maintenance can result in potentially unsafe water.” It points to the Water Quality Association at wqa.org for more information.

Sources

  1. U.S. EPA, “CCR Information for Consumers.” epa.gov. Accessed November 18, 2026.
  2. City of Dallas, 2025 Water Quality Report (definitions, contacts). PDF, and the full data version with the nitrate row, 2025 WQR-ENG-FINAL PDF. Accessed November 18, 2026.
  3. City of Dallas, Dallas Water Utilities memorandum, December 1, 2023 (hardness range). PDF. Accessed November 18, 2026.
  4. City of Phoenix Water Services Department, 2025 Water Quality Report. PDF. Accessed November 18, 2026.
  5. U.S. Geological Survey, Water Science School, “Hardness of Water.” usgs.gov. Accessed November 18, 2026.

Questions

What is a Consumer Confidence Report (CCR)?

It is the annual drinking water quality report that the EPA requires community water systems to deliver to their customers.

When do water quality reports come out?

According to the EPA, your water supplier must send the report each year by July 1.

Where can I get my water quality report?

Call your local water supplier, check its website, or use the CCR search tool linked from the EPA's consumer information page.

Why is there no hardness number in my water report?

Hardness is not a regulated health standard, so some reports leave it out. The City of Dallas 2025 report, for example, lists no hardness figure. Ask your utility directly or test your own tap.

Is ppm the same as mg/L?

Yes. The City of Dallas report defines ppm as parts per million, or milligrams per liter (mg/L).

Published November 18, 2026 · Updated November 18, 2026.